2617 - One Off Used Davis Standard Automotive Telecoms Wire Coating Line 2008

Combination of Lots 1 to 19 - One Off Used Davis Standard Automotive Telecoms Wire Coating Line

Please Note: this lot is located in Swindon and will be loaded free of charge to a suitable vehicle. Blocking and securing will be at the cost of the purchaser.

M48 Dancer Unit. SO/No. 85941, S/No. BX022 (2008)

Please Note: this lot is located in Swindon and will be loaded free of charge to a suitable vehicle. Blocking and securing will be at the cost of the purchaser.

Davis Standard Thermatic Extruder 25-IN-25 and Control Unit, 2.5” (63 mm) Bore, 24:1 L/D Ratio, Type DSPA, Heavy Duty, Fabricated Steel Base with Rigid Steel Front Barrel Support, Vertically Adjustable Motor Base for 50 HP Drive Motor with Encoder, Belts, Sheaves and Belt Guard for 100 RPM Screw Speed, Heavy Duty Gearbox with 17.56:1 Ratio Utilizing Helical Gearing and Positive Internal Lubrication. Gearbox Rated at 95 HP (71 Kw) at 100 RPM with A 1.25 Service Factor, Pre-Loaded Thrust Bearing with A B-10 Life Of 544,000 Hours at 5,000 PSI (344 BAR) and 100 RPM, Cast Iron Feed Section with Full Water Jacket, Alloy Steel Barrel with DS-6000 Bimetallic Liner, Drilled and Tapped for Pressure Transducer, Cast Aluminium, ...

3m (Approx.) Slide Through of Stainless Steel Cooling Trough, SO/No. 85945, S/No. BX026 (2008), Entry Catch Basin on 1m Telescoping Section (Rack and Pinion), Water Entry Though Nozzles Located Over Trough, (1) 3m Trough with (1) Stand, “V” Bottom Design / Flood Design, Exit Catch Basin with Air Wipes

Please Note: this lot is located in Swindon and will be loaded free of charge to a suitable vehicle. Blocking and securing will be at the cost of the purchaser.

MPT-18 Multi-Pass Cooling System with 6m, (2) x 3m Joined Sections of 14 gauge (1.9mm Thick) #304 Stainless Steel Cooling Trough, Each 3m Section of Trough is equipped with (8) x Water Spray Nozzles, (2) x Hand Valves, (1) x Drain and (1) x Gasketed Cover, Solenoid Valve Is Installed in the Water Supply Manifold, aach Hand-Operated Valve Adjusts (4) x Water Spray Nozzles. Pneumatic Lines are Installed to the Air Cylinders and Push Button-Operated Solenoid Valves are Supplied to Open and Close the Covers, A Bank of Four, 2 Groove UHMW Sheaves is Mounted at Each End within The Cooling System, Plexiglass” Windows are Provided in The Areas of the Cover over the Sheave Banks, Ceramic-Coated Rods are Mounted at intervals ...

Davis-Standard Cable Dryer with (2) Nozzles with Lid, Cable Guides Before, Between and After the Nozzles with Ceramic Inserts, (2) Gas Ring Blowers, HP Each with Hoses, (1) Rack with Height Adjustable Supports for Housing, Totally Enclosed, Noise Insulation, Bulkheads at Entry and Exits. S/O No. 85941, S/No. BX034 (2008)

Please Note: this lot is located in Swindon and will be loaded free of charge to a suitable vehicle. Blocking and securing will be at the cost of the purchaser.

Davis-Standard High Speed Air Wiper Assembly for .500” (12mm) Diameter Maximum Primary Wires and Small Cables. This Unit is Supplied with a Sturdy Base for Mounting as A Free-Standing Unit Separate From The Capstan Or Trough, Wire Entry Height Is Adjustable from 38 To 43 ¼” (965 to 1098 mm). This Unit has a Three (3) HP (2.2 KW) Vacuum Blower, Motor Starter and Pushbutton Station Prewired to a NEMA 12 (IP-65) Junction Box, Vacuum Wiper Head is 36” (914 mm) Long, Vacuum Gauge and a Replaceable Wear Strip. SO/No. 85941, S/No. BX054. (2008)

Please Note: this lot is located in Swindon and will be loaded free of charge to a suitable vehicle. Blocking and securing will be at the cost of the purchaser.

Davis-Standard DC-16, 16” Dual Drum Capstan to Provide Non-Slip Pulling of Small to Intermediate Diameter Wire. Stainless Steel Bi-Fold Doors on The Front of The Housing Provide Easy Access or Thread-Up.The Two, 16” (406 Mm) Diameter Capstan Drums are Fabricated from SS 410, (5) Grooves for Maximum Cable Diameter 0.37” (9.40MM) and are Mounted on Self-Aligning, Ball Bearing Pillow Blocks with Adjustment for Tilting the Drums to Provide a Scuff-Free Wire Path. the Root Diameter of The Drums is Machined within +/- 0.001” TIR. The Drum Shafts are Coupled by “V”-Belts to Prevent Wire Stretching During Rapid Speed Changes. SO/85941. S/No. BX036 (2008)

Please Note: this lot is located in Swindon and will be loaded free of ...

Zumbach ODAC 18XY-DP, 31538 ODAC 18XY-DP Dia. Scanner .003/.71". S/No. 2805.24.1710.1

Please Note: this lot is located in Swindon and will be loaded free of charge to a suitable vehicle. Blocking and securing will be at the cost of the purchaser.

Zumbach DST AST.ISF.12.40.C. S/No. 2808.3678.20

Please Note: this lot is located in Swindon and will be loaded free of charge to a suitable vehicle. Blocking and securing will be at the cost of the purchaser.